Last updated:
The air conditioner is wearing out, and every cold morning the electric furnace in the closet heats the house on its resistance strips alone. You’re wondering whether one heat pump should handle both seasons, and where its outdoor unit should go in a yard that holds water.
Sweet Olive installs ducted air-source heat pumps and replaces older systems in Estelle and across our service area. Moving from an air conditioner and electric furnace to a heat pump usually keeps the ducts and changes the equipment at both ends. In Estelle the permit goes to Jefferson Parish. On the first visit we size the system from your rooms, check the furnace circuit and walk the whole yard. Your written estimate names the equipment, the backup heat, the outdoor spot and the parish permit steps.
If the system still has life in it, start with maintenance or a repair. The conversion page explains the switch in full, and the central AC comparison sets out the difference.
What an AC-to-heat-pump swap in Estelle looks like
A tired air conditioner, an electric furnace doing all the heating and a back corner that holds rainwater: one Estelle conversion, decided around the yard.


- Location
- Estelle, off Barataria Boulevard
- Home
- Single-story slab house, about 1,800 sq ft, four bedrooms
- System
- Nominal 3-ton two-stage heat pump with an 8 kW heat strip
- Replaced
- Central AC and electric furnace
- Outdoor unit
- Moved to a 24-inch stand by the back wall
- Access
- 36-inch side gate, utility-closet air handler
- Project price
- $8,350
- Duration
- 2 working days
The setting
Electric heat and a wet corner
The house is a single-story slab home off Barataria Boulevard in Estelle, about 1,800 square feet with four bedrooms. A central air conditioner cools it and an electric furnace in the utility closet heats it on resistance strips alone. The air conditioner is failing. Its outdoor unit sits on a pad in the back corner of the yard, where water stands for hours after a heavy rain.
The decision
A heat pump that heats, and a drier spot
Replacing the air conditioner like for like keeps the resistance strips as the only heat. A heat pump moves heat instead of making it, and keeps an 8 kW strip for the coldest mornings. The load calculation supports a nominal three-ton, two-stage system. We move the outdoor unit to a 24-inch stand against the back wall, the higher part of the yard, once the parcel's floodplain requirement is checked.
The work
Two days through a 36-inch gate
Day one recovers the refrigerant, takes the old units out through the side gate and sets the new air handler in the closet on the existing duct connections, which test sound. The existing furnace circuit stays after we check its breaker and wire against the new nameplate. Day two bolts the stand to its footings, runs a new 15-foot line set, brazes under nitrogen, pressure-tests and evacuates, and fills the old pad's spot with soil.
The handover
Defrost and backup heat confirmed
We check the charge, airflow and static pressure, test the drain, then confirm the defrost cycle and the heat strip and set the thermostat so the strip runs only when the heat pump needs help. The readings stay with the owner, and the Jefferson Parish inspection follows. The aim is a house that leans on the heat pump through most of the winter, with the strip saved for the cold mornings, and an outdoor unit that stays out of standing water.
From resistance heat to a heat pump
An electric furnace makes heat; a heat pump moves it, and that changes how the winter feels on the bill.
54.3°F
Average daily temperature in January at the New Orleans airport, from National Weather Service climate normals
Most winter hours here are mild, which is when a heat pump does its best work and the backup strip can stay off.
What changes and what stays
The outdoor air conditioner and the indoor furnace cabinet both come out, replaced by a heat pump and its matched air handler. Sound ducts stay, after we test them for leakage and static pressure. The furnace’s circuit can often carry the new air handler’s heat strip once we check its breaker and wire against the nameplate.


Sizing the strip, not the biggest one
A heat strip covers defrost and the coldest mornings. We size it from your heating load in the room-by-room calculation (ACCA Manual J), not at the largest strip the cabinet accepts, and set the thermostat so it stays off on mild days. The cold-weather guide explains how a heat pump behaves in a cold snap.
Four bedrooms on one system
In a larger single-story house, the far bedrooms sit at the end of long duct runs. We check those runs and the return path from each room, and long or crushed runs go into a ductwork repair line instead of a bigger unit.
Yards at the edge of the wetlands
Estelle reaches south toward the Barataria Preserve, and heavy rain finds the low corners of its yards.
Next to the preserve
The Barataria Preserve, part of Jean Lafitte National Historical Park and Preserve, covers about 26,000 acres of bayous, swamps, marshes and forest just outside Marrero, along the southern edge of Estelle. Yards on this side of the West Bank can hold water for hours after a summer storm, and the outdoor unit is often in the lowest corner.
Choosing the spot and the height
Heating and cooling equipment isn’t built to sit in water. We look at where it stands after rain, then check the parcel’s floodplain requirement with Jefferson Parish before keeping the old pad, pouring a new one or setting a stand. Manufacturers set clearances around the coil and the service panel, and a short line set to a higher spot is often worth it. The placement guide shows the options.

Permits and the Marrero mailing address
Estelle is unincorporated Jefferson Parish, and its addresses don't always say so.
One parish office
Installing or replacing heating and cooling equipment in Estelle is filed with the Jefferson Parish Building Regulatory Division before the work, and inspected after. Some Estelle addresses carry a Marrero mailing city; Marrero and Woodmere go to the same parish office, so the filing is the same. Your estimate states who obtains the permit, and the permit guide compares the offices.
The electric account
We confirm which utility serves your account at the visit. Rebate programs depend on it, so we never count one in your budget until it is confirmed.
What an Estelle swap costs
Our range is the same here; the yard, the ducts and the circuit decide where you land.
Sweet Olive's typical range for a residential ducted heat pump replacement is $4,250 to $11,750. We set your price after the site visit and write it into your estimate line by line, with any stand, duct work and the Jefferson Parish permit steps shown separately.
What moves an Estelle price
- Equipment and strip. Capacity and stages from the load calculation, and the heat strip size.
- The outdoor spot. Keeping the pad, a new pad, or a stand on a higher part of the yard.
- The ducts. Sealing joints or repairing long runs to the far bedrooms.
- The circuit. Reusing the furnace circuit after a check, or adding one.
- Controls. A thermostat that runs the strip only when needed.
The cost guide breaks a price into its parts.
