Last updated:
The heat pump kicks on, runs a few minutes and stops, over and over, and the den still feels warm. Out back, the outdoor unit sits up at floor level on a platform whose boards have started to give. Is it time to replace the system, and what should hold the new one?
Sweet Olive installs and replaces ducted air-source heat pumps in homes across Chalmette and the rest of our service area. Chalmette is the seat of St. Bernard Parish, and the parish handles the permit. On the first visit we test the system before blaming it, check the attic ducts and the panel, and look hard at whatever holds the outdoor unit. Your written estimate lists the equipment, any stand or platform work and the parish permit steps.
If the system might be saved, start with repair. If it is done, the replacement page covers the decision, and the warning signs guide helps you read the symptoms.
What a Chalmette replacement on a raised house looks like
An outdoor unit raised on a softening wood platform, a failing system and a St. Bernard Parish filing.


- Location
- Buccaneer Villa North, Chalmette
- Home
- Single-story raised home, about 1,450 sq ft, two bedrooms and a den
- System
- Nominal 2.5-ton single-stage heat pump
- Outdoor unit
- Moved from a wood platform to a galvanized steel stand at the same height
- Air handler
- Attic, over the hall
- Drain
- Rerouted to the exterior with a new trap
- Line set
- 28 feet, new
- Project price
- $8,150
- Duration
- 2 working days
The setting
Equipment up high, platform giving way
The house is a single-story raised home in Buccaneer Villa North, about 1,450 square feet with two bedrooms and a den. The heat pump that went in when the house was raised now short-cycles and leaves the den warm. Its outdoor unit sits up off the ground on a wood platform beside the back stairs, and the platform's boards have started to soften.
The decision
Keep it high, change what holds it
Bringing the outdoor unit down to a pad at grade was the alternative, with a shorter, easier service reach. The owners want it kept up, so we replace the wood platform with a galvanized steel stand at the same height. The load calculation supports a nominal two-and-a-half-ton system, and the attic ducts test sound apart from a loose collar at the den branch.
The work
Stand, unit, then the attic
Day one recovers the refrigerant, lowers the old outdoor unit, removes the platform, and sets and anchors the steel stand with a new disconnect at its height. The new unit goes on top. In the attic, the new air handler goes over the hall on a fresh secondary pan and float switch, and the drain is rerouted to the outside with a new trap. Day two runs a new 28-foot line set, brazed under nitrogen and evacuated to a micron reading.
The handover
A cooler den, a sturdier stand
We reseal the den collar with mastic, set the thermostat, test the float switch and record airflow and charge. St. Bernard Parish inspects after the work. The aim is steady cooling in the den and outdoor equipment that sits on something built for it.
Houses rebuilt, raised or both
Chalmette's houses sit at different heights, and the equipment follows the house.
When the house went up
Hurricane Katrina flooded most of Chalmette in 2005, and many houses were rebuilt in the years after, some raised on piers or higher foundations. Where a house was raised, the outdoor unit generally goes up with it, onto a wood platform or a steel stand near the back steps, and the air handler may sit in the attic or a closet. We size a replacement from the house as it stands now, with a room-by-room load calculation.
When it stayed on the slab
Slab houses keep the outdoor unit on a pad at grade. We look at where water stands after a heavy storm and check the parcel’s requirements before deciding whether the pad stays or the unit goes onto a stand. The placement guide covers clearances too.

Short cycling: what it can mean
A system that keeps stopping isn't always a system that needs replacing.
Causes we check before quoting
- Oversized equipment. It hits the setpoint fast and stops before drying the air.
- Refrigerant charge. Low charge can trip safety controls.
- A failing part. A capacitor, contactor or sensor acting up.
- Thermostat placement. A control in sun or in a supply draft misreads the room.
- Ducts. A loose run starving one room while the hall satisfies the thermostat.

Repair, or replace with the right size
If a part is the cause and the system is otherwise sound, a repair may be the better spend. If the equipment was oversized from the start or is near the end, replacement lets us size it correctly. The components guide explains the parts involved, and the sizing guide shows the load calculation.
Permit and power in St. Bernard Parish
A separate parish, with its own forms.
St. Bernard Parish keeps its own mechanical permit application and safety-permit process, so Chalmette heating and cooling work is filed there, not with New Orleans. The parish line with the city runs past Arabi, a few minutes upriver. Your estimate states who obtains the permit, and the permit guide covers the steps.
Chalmette homes are generally on Entergy Louisiana accounts. The Energy Smart rebate is for Entergy New Orleans residential accounts, so we confirm your account before counting any incentive.
What a Chalmette replacement costs
Our range holds across the parish line; your house sets the figure.
Sweet Olive's typical range for a residential ducted heat pump replacement is $4,250 to $11,750. We set your price after the site visit and write it into your estimate line by line, with any stand or platform work and the St. Bernard Parish permit steps shown separately.
What moves a Chalmette price
- What holds the outdoor unit. Reusing a sound stand, or a new steel stand or pad.
- Height and distance. A longer line set from a raised unit to an attic air handler.
- Attic access. Pull-down stair, platform, and a new secondary pan and float switch.
- Equipment. Capacity from the load calculation, single-stage or two-stage.
- Ducts and drain. Resealing loose collars, rerouting a drain line.

