Last updated:

The short answer

A thermostat works with a heat pump if it can switch the reversing valve, call each compressor stage, run the backup heat on its own call and work with the equipment's controls. Many variable-speed systems need the maker's own communicating thermostat. Check the equipment's model numbers and the existing wiring before buying a new control.

Key takeaways

  • A heat pump control runs the reversing valve, the stages, the fan and the backup heat.
  • A screen that fits the wall doesn't prove it can talk to the equipment behind it.
  • Communicating systems usually need the manufacturer's own control to use their features.
  • Backup-heat lockouts, fan mode and setbacks change both comfort and the bill.
  • Leave wiring changes to a technician; the safety controls stay connected.

A new thermostat is one of the cheapest parts of a heat pump system and one of the easiest to get wrong. A control that only knows how to run an air conditioner can leave a heat pump heating on its backup strip, running one stage of two, or ignoring a dehumidifying setting the equipment was chosen for.

Sweet Olive installs ducted heat pumps across New Orleans and chooses the control with the equipment on every installation. This guide covers what the control has to run, how to check a new one before you buy it, and the settings that change comfort and the bill.

What a heat pump thermostat has to control

Each function below is a separate instruction from the control to the equipment. Missing any of them changes how the system runs.

Function Marking usually seen Without it
Reversing valve, which switches between heating and cooling O/B The system heats when it should cool, or the reverse
Compressor, low stage and high stage Y1, Y2 A two-stage system runs one way only, like an oversized one
Backup heat, automatic W2 or AUX The strip can’t come on, or comes on with no lockout
Emergency heat, manual E No way to heat on the backup alone if the outdoor unit fails
Indoor fan G No fan-only setting; the blower runs only with heating or cooling
Steady power for the control C Powered and smart controls drop out or drain their batteries
Communicating link Set by the manufacturer A variable-speed system runs with limited features, or not at all

The functions a heat pump control runs, the marking usually seen at the thermostat, and what goes wrong without each one.

New air handler in a hall closet with the removed gas furnace on a hand truck in the hallway
An air handler in its closet; the thermostat cable ends at the control board inside this cabinet.

Markings are a guide, not a wiring plan

The markings above are common, but makers differ, and the reversing valve can be set to switch on heating or on cooling. We read the equipment’s own diagrams before connecting anything. Safety controls, such as the float switch on the drain, stay wired in.

Stages and moisture

A staged or variable-speed system runs long at low output in mild, damp weather, which dries the air. A control that can’t call the low stage throws that away. Our staging comparison explains why it matters here.

Check before you buy a new control

A few facts about your equipment and the cable in the wall answer most compatibility questions.

Conventional control

Separate wires carry each instruction to the equipment.

  • Works with many single-stage and two-stage systems
  • Needs enough conductors for every function used
  • Often needs a common wire for a powered or smart model

Communicating control

A few wires carry digital messages between the control and the equipment.

  • Used by many variable-speed systems
  • Usually the manufacturer's own control
  • Unlocks dehumidifying, fault messages and fine staging

Match the control to the equipment first, then pick the features you want.

What to gather

  • The model numbers of the outdoor unit and the air handler or furnace, from their labels.
  • A photo of the current thermostat, front and model.
  • The number of conductors in the cable at the wall, if the control lifts off its base without tools; don’t disconnect anything.
  • Whether the house has a gas furnace as backup, which needs a dual-fuel control.
  • What you want from the control: schedules, remote access, humidity readings.
New heat pump on a rear pad behind a Slidell cottage
An outdoor unit on its pad; its model number tells us whether the system is staged, variable-speed or communicating.

Settings that change comfort and cost

The same equipment can feel and cost very different amounts depending on a handful of settings.

Setting What it does What to watch
Backup heat lockout Keeps the strip off above a chosen outdoor temperature Too high a lockout runs the strip on mild mornings
Compressor lockout or dual-fuel changeover Hands heating to the furnace below a set temperature Set from the equipment, the house and your rates
Fan mode: auto or on Auto runs the fan with heating or cooling; on runs it all the time Fan on between cycles can blow moisture from the wet coil back into the house
Dehumidifying Slows the blower so the coil pulls more water out Only on equipment and controls that support it
Setbacks and recovery Lowers or raises the setpoint while you are out or asleep A big winter setback can bring on the strip to recover
Cycle rate How often the system may start in an hour Too fast causes short cycling; set to the equipment

Thermostat settings that matter on a heat pump, what each does and what to watch.

Setbacks on a heat pump

A heat pump recovers slowly from a deep setback, so many controls bring on the strip to catch up. Small setbacks, or a control with heat pump recovery logic, avoid that. Our cold-weather guide and operating cost guide cover the effect on the bill.

Fan on, and why rooms feel damp

Running the fan between cycles keeps air moving, but it also blows over a wet coil and returns some of that water to the rooms. In a humid summer that can undo the drying. Our humidity guide explains the moisture side.

Drop cloths laid across the porch and through the front door of a raised New Orleans house
A deep porch on a humid afternoon, the kind of weather where fan mode decides how damp the rooms feel.

Smart thermostats on a heat pump

Smart controls can work well with heat pumps, as long as they can run every function and have steady power.

What to confirm for a smart control

  • It lists heat pump support with the reversing valve setting your equipment uses.
  • It runs the stages and backup heat your system has, including dual fuel if you keep a furnace.
  • It has steady power, through a common wire or an adapter its maker approves.
  • Its away and schedule features don’t trigger deep setbacks that bring on the strip.
  • It isn’t replacing a communicating control the equipment needs for its full features.
Connected front rooms of a New Orleans shotgun double with ceiling supply registers
Front rooms joined by a wide opening; a control in a central room reads the house better than one at the far end.

Where the thermostat sits, and what we set at handover

Placement decides what temperature the control reads. Setup decides what it does with it.

BedroomBedroomBedroomHallBathLivingKitchen
  • Dark circle, Each room: windows, sun and ceiling height for the load calculation
  • Ochre square, Attic opening: headroom and joists
  • Blue diamond, Return location: where a central return can draw air
  • Yellow triangle, Electrical panel: rating, open spaces and existing load
  • Open ring, Outdoor spot: footing and drainage
  • Dark cross, Thermostat: on an inside wall
A floor plan with the first-visit stops, including the thermostat on an inside hall wall, away from sun and supply registers.

A good spot on the wall

The control belongs on an inside wall in a room you use, about at eye level, away from windows, supply registers, lamps, the kitchen and outside doors. A control in the wrong spot reads a different house from the one you live in.

What we set at handover

At startup we set the stages and the backup heat, record them, and go through the normal setup with you: modes, fan, schedules and the backup-heat settings. Follow your system’s own guidance rather than a neighbour’s settings. Our components guide and dual-fuel guide cover the rest of the system the control runs.